The Measure of Quality
Product News


A variety of accessories are available to help you get the most from your PosiTector RTR.

Optical Grade Replica Tape available
Povides higher quality SDF surface data files than
conventional replica tape. (For use with RTR-P models

Testex™ Press-O-Film™ Replica Tape

50 pieces (impressions) per roll

Tape Grade Range Order Code
Coarse (C) 20 to 64 microns
0.8 to 2.5 mils
X-Coarse (XC) 40 to 115 microns
1.5 to 4.5 mils

Optical Grade
Coarse (C)

20 to 64 microns
0.8 to 2.5 mils
Optical Grade
X-Coarse (XC)
40 to 115 microns
1.5 to 4.5 mils

Certificate of Conformity
Warranty Information (XC Press-O-Film)

Testex Tape is not included with PosiTector RTR

Certified PosiTector RTR Shim Set

Used to verify the accuracy and operation of PosiTector RTR and other spring micrometer replica tape readers. Ideal for fulfilling both ISO and in-house quality control requirements. Includes Certificate of Calibration traceable to PTB.

Accuracy: ±1.25 microns 

The shims, along with our calibration procedure, allow you to verify the height (H, HL) accuracy of PosiTector RTR instruments in-house

PosiTector RTR Check Shim
Order Code: RTRCHKSHIM04

Used to check PosiTector RTR peak height accuracy (RTR-H and RTR-P). One check shim is included with each probe.

Stated thickness is adjusted for Replica Tape Offset Value.

PosiTector RTR Check Tape
Order Code: RTRCHKTAPE04

Used to check the operation of PosiTector RTR-P peak density measurement (for use with the PosiTector RTR-P only).

One check tape is included with each RTR-P probe.


Cleaning Cards

Pre-moistened with isopropyl alcohol to clean residual adhesive and debris from the anvils helping to insure an accurate test.

Every PosiTector RTR ships with (5) cleaning cards. Additional cards are available (20 cards per pack).


Surface Cleaning Putty
Order Code: RTRPUTTY

To clean the test surface of debris prior to burnishing

Every PosiTector RTR ships with 1 package of cleaning putty. Additional putty is available (5 per pack).


Stainless Steel Burnishing Tool

Round-end (Ø8 mm) rubbing tool to compress replica film on the blasted surface.

One burnish tool is included with each PosiTector RTR probe.



Bluetooth Printer

receives data from Advanced models

  • Receives data via Bluetooth wireless technology.
  • Prints readings and statistical summary
  • Battery-operated
  • Light weight
  • One year Warranty

Bluetooth Transfer Overview 


SAC Power Kit
Order Code: USBAC

for continuous operation or battery charging

This kit supplies several alternate power solutions for your battery-operated PosiTector. They allow the gage to operate continuously without the need for batteries.

Use the cable alone to connect a PosiTector to your PC's built-in USB port that acts as a continuous power source. Or connect the cable to the included power adaptor which plugs into any AC wall electrical outlet, 110 or 220V.

A selection of electrical plugs is included which are capable of dealing with most country’s outlets.


PosiTector Case
Order Code: CASEINSP

Convenient hard shell case for carrying a PosiTector gage body and multiple probes - including any of the PosiTector 6000 Coating Thickness probes, DPM Dew Point Meter probes, RTR/SPG Surface Profile probes, or UTG Ultrasonic Wall Thickness probes.

Case has compartments for Certificates of Calibration, instruction manuals and other accessories. 

Rechargeable Batteries

  • eneloop HR4UTG (NiMH 800 AAA 1.2V)
  • Precharged and ready to use immediately
  • Considerably longer run time than conventional Nickel Cadmium batteries
  • Low self-discharge: once charged, eneloop rechargeable batteries keep 90% of their charge after 6 months and 85% after 12 months
  • High performance at low temperatures down to -10 °C
  • No charger required - Recharge batteries inside the PosiTector when connected via USB.
  • eneloop website:


Protective Lens Shield

  • Pack of five thin plastic lens shields
  • Ideal for protecting the PosiTector display from paint overspray.

One lens shield is included with every PosiTector instrument

PosiTector Probes

PosiTector body accepts all PosiTector RTR, SPG, 6000, 200, DPM, and UTG probes easily converting from a coating thickness gage to a dew point meter, surface profile gage or wall thickness gage



What's New]
[Products ] [Service & Support] [Join our Team]
[Terms & Conditions] [Privacy] [Resources] [Contact Us]
[Site Map]

©2017 DeFelsko Corporation.