Testex™ Press-O-Film™ Replica Tape

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Verify accuracy/operation of coating thickness gages. Important component of fulfilling both ISO/QS-9000 and in-house quality control requirements with a measurement accuracy traceable to NIST or PTB.

Economical alternative to Coated Metal Plates, with a reduced accuracy. Ideal for protecting the PosiTector probe tip.

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

Every PosiTector 200 and PosiTector UTG ships with (1) bottle of Ultrasonic couplant.  Additional 4oz. bottles are available (sold in cases of 12). MSDS

Use for continuous operation or battery charging. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

Convenient hard shell case for carrying a PosiTector gage body and multiple probes

Precharged batteries ready to use with a considerably longer run time than conventional Nickel Cadmium batteries. High performance in low temperatures and no charger required.

Pack of 5 thin plastic lens shields to protect PosiTector display from paint overspray. One lens shield included in every PosiTector purchase.

Certified Polystyrene Blocks are for use with gages that measure over 1500 µm (60 mils).

Ideal for use on thin, soft coatings to protect unnecessary wear while using Scan or Fast mode to measure large objects

Helps reduce adverse operator influence by ensuring the probe is placed perpendicular to the part’s surface in a controlled, repeatable way.

Provides a quick accuracy check of the instrument and allows the user to perform practice measurements

Used to verify the accuracy and operation of surface profile depth micrometers

Replacement probe tips - 2 angles available: 60° or 30° 

50 pieces (impressions) per roll

Used to verify the accuracy and operation of PosiTector RTR and other spring micrometer replica tape readers

Used to check PosiTector RTR peak height accuracy (RTR H and RTR 3D). One check shim is included with each probe.

Used to check the operation of PosiTector RTR 3D peak density measurement (for use with the PosiTector RTR 3D only).

Pre-moistened with isopropyl alcohol to clean residual adhesive and debris from the anvils helping to insure an accurate test.

To clean the test surface of debris prior to burnishing

Round-end (Ø8 mm) rubbing tool to compress replica film on the blasted surface.

Hand-held Surface Temperature Probe and Liquid Temperature Probe. For use with PosiTector DPMS probes only.

For use with existing conductivity meters. Try the revolutionary, reusable PosiPatch with a low cost trial pack.

Ideal for checking the operation of durometers.

Helps reduce operator influence by ensuring the probe is placed perpendicular in a controlled, repeatable way.

For use with threaded mounts in other test stands and calibrators.

Ideal for checking calibration and operation of ultrasonic thickness gages and are an important component in fulfilling both ISO and in-house quality control requirements.

Genuine leather pouch protects your PosiTest DFT while keeping it within easy reach.

Used to protect the probe transducer (Qty. 2)

Includes adaptable sponge hardware and accessories to convert the PosiTest LPD Basic Kit into a PosiTest LPD Complete Kit.

Extend the PosiTest LPD base rod an additional 0.3 m (1')

Pinholes can be so miniscule that water has difficulty reaching the conductive substrate underneath. Use a surfactant (wetting agent) to lower the surface tension of the water.

For verification of electrical resistance

Interchangeable stand-off allows a PosiTest ATM20 or ATA20 to pull 50 mm dollies. Ideal for lower bond strength finishes such as coatings on wood, concrete and plastic.

Interchangeable stand-off allows a PosiTest ATM50 or ATA50 to pull 10, 14 and 20 mm dollies. Ideal for high bond strength finishes such as coatings on metal.

Loading fixtures, stubs for adhesion testing.

Drilling template and drill bits to isolate test area, ideal for thicker coatings on concrete.

Additional glue, mixing sticks, palettes and cotton swabs.

Ideal for checking the accuracy and operation of PosiTest Adhesion Testers and is an important component in fulfilling both ISO and in-house quality control requirements.

Every PosiTest AIR comes complete with (4) bottles of Test Solution. Additional bottles are available in cases of (16) 8 oz. bottles.

The PosiTector SHD Verifier is ideal for checking accuracy and operation of Shore hardness durometers and is an important component in fulfilling both ISO and in-house quality control requirements.

Like the Standard Magnetic Ring PosiPatch, the NEW Flexible Magnetic ring leaves no messy adhesive residue to clean but is intended for pipes and other tight-diameters.

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTest instrument.

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTector instrument.

For best results when acquiring a 2D/3D parameters and images, it is recommended to use the supplied burnishing ball instead of the stainless-steel burnishing tool.

For best results and to minimize the migration of adhesive from the tape to the probes measurement system, DeFelsko recommends using the supplied tape holder.

Interchangeable stand-off allows a PosiTest ATM or ATA to pull 50 mm x 50 mm square dollies conforming to BS EN 12004-2. Ideal for cementitious adhesive for tiles.

Interchangeable stand-off allows a PosiTest ATM or ATA to pull 50 mm dollies conforming to ASTM C1583. Ideal for concrete surfaces and overlays.

Purified, ion-free water, 250 ml or 1 l

To verify probe accuracy

Replacement extraction tool for use with the PosiTector CMM IS.

Available in packs of 3.

Replacement caps for use with the PosiTector CMM IS

Add additional, reusable PosiTector CMM IS Smart probes

Available in packs of ten A-76/LR-44 coin cell batteries for use with the PosiTector CMM IS.

A 10-pack of the Salt Solution for use with the PosiTector CMM IS

Replacement fins for the PosiTector CMM IS

100 pack - 125 mm for use with Abrasives Test Kit

Measures the concentration of water-soluble contaminates in blast cleaning abrasives

A lightweight, portable device that allows you to extend the reach of your PosiTector 6000 regular cabled probes.

For verifying the operation of Barcol hardness impressors. Choose from hard or soft aluminum alloys. (Pack of 5)

For zeroing worn or replaced indentors on the PosiTector BHI.

Includes additional spare indentor tips (2pk) with replacement tool for the PosiTector BHI.

Provide a quick operational check of the instrument by allowing the user to perform practice measurements

Ideal for applications where the USB cable will stay connected while taking measurements.

Steel pipe electrodes — assorted sizes available: 10 to 60 cm (4 – 24”) Rolling springs include two pre-installed spring couplers.

Stainless steel — assorted sizes available: 5 to 120 cm (2 – 48”)

Stainless steel — 5 cm (2”)

Converts the PosiTest HHD to a wand-type instrument

Choose between 13 cm (5") and 50 cm (20") rods

Connect to spring and brush electrodes from other manufacturers

Standalone voltmeter (crest meter, jeep meter) for verifying the accuracy and operation of ALL pulse type and DC holiday detectors

‍

Thread onto rolling springs and attach to the Spring Connector

Connect the PosiTest HHD to DeFelsko or SPY rolling spring electrodes

102mm/4" Conductive Rubber Paddle for PosiTest HHD

For enhanced stability on 30 - 45 cm (12 - 18") OD pipes (for PosiTector SPG OS only).

Converts the PosiTest LPD Low voltage Pinhole Detector into a cabled-wand style unit.

Adaptable Sponge Hardware for a variety of test configurations.

Reusable patch with Standard or Flexible magnetic ring

Self-adhesive, polyurethane patches

Latex patch with easy-open tabs and low-tack adhesive for easy removal