Accessories

PosiTector Gage Bodies can be used with all PosiTector probes. Choose from Standard or Advanced models.

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Round-end plastic rubbing tool to compress replica film on the blasted surface (Pack of 10)

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

Convenient hard shell case for carrying a PosiTector gage body and multiple probes

Each roll of Testex Tape includes 50 pieces (Impressions)

Used to verify the accuracy and operation of all Testex micrometers. Ideal for fulfilling both ISO and in-house quality control requirements. Includes Certificate of Calibration traceable to PTB.

‍

Use for continuous operation. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTector instrument.

For best results when acquiring 2D/3D parameters and images, it is recommended to use the supplied burnishing ball instead of the high accuracy burnishing tool.

Used to check PosiTector RTR peak height accuracy (RTR H and RTR 3D). One check shim is included with each probe.

For best results and to minimize the migration of adhesive from the tape to the probes measurement system, DeFelsko recommends using the supplied tape holder.

To clean the test surface of debris prior to burnishing

Used to verify the operation of Testex and other spring micrometer replica tape readers

Pre-moistened with isopropyl alcohol to clean residual adhesive and debris from the PosiTector RTR and RTR 3D anvils helping to ensure an accurate test.

Burnishing tool includes a built-in spring mechanism ensuring that consistent force is used, regardless of how hard the tool is pressed against the surface

ICRI Concrete Surface Profile Chips available with or without Technical Guideline

Belt Clip for PosiTector gage bodies

Used to verify the accuracy and operation of surface profile depth micrometers

Used to check the operation of PosiTector RTR 3D peak density measurement (for use with the PosiTector RTR 3D only).

Replacement probe tips for the PosiTector SPG — 2 angles available: 60° or 30° 

For enhanced stability on 30 - 45 cm (12 - 18") OD pipes (for PosiTector SPG OS only).

Pack of 5 thin plastic lens shields to protect PosiTector display from paint overspray. One lens shield included in every PosiTector purchase.

Provides a quick accuracy check of the PosiTector SPG and allows the user to perform practice measurements

PosiTector Gage Bodies can be used with all PosiTector probes. Choose from Standard or Advanced models.

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Dew Point Meter Logger attaches to steel structures to measure and record environmental parameters independently for up to 200 days.

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

Convenient hard shell case for carrying a PosiTector gage body and multiple probes

Use for continuous operation. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTector instrument.

10 pack of replacement filters for the PosiTector DPM L and PosiTector DPM L+

Belt Clip for PosiTector gage bodies

Available in packs of five (5) CR2032 batteries.

For use with the PosiTector DPM L.

Optional Lock for PosiTector DPM L Series.

Keeps both PosiTector DPM L and PosiTector DPM L+ safe and secure.

Hand-held Surface Temperature Probe and Liquid Temperature Probe. For use with PosiTector DPMS probes only.

Pack of 5 thin plastic lens shields to protect PosiTector display from paint overspray. One lens shield included in every PosiTector purchase.

Reusable Bresle Test patch with Standard or Flexible magnetic ring for soluble salt testing

Latex Bresle Test patch with easy-open tabs and low-tack adhesive for easy removal for soluble salt testing

Self-adhesive, polyurethane Bresle Test patches for soluble salt testing

PosiTector Gage Bodies can be used with all PosiTector probes. Choose from Standard or Advanced models.

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

For use with existing conductivity meters. Try the revolutionary, reusable Bresle Method PosiPatch with a low cost trial pack.

For use with the innovative PosiPatch. Holds Bresle test patches on steel surfaces without leaving any messy residue.

Measures the concentration of water-soluble contaminates in blast cleaning abrasives

Use for continuous operation. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

Purified, ion-free water to be used with the PosiTector SST, 250 ml or 1 l

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTector instrument.

To verify accuracy of PosiTector SST probe

(1) Roll of ISO 8502-3 Tape for use with PosiTest DT test—25 mm wide

Replacement dust tape comparator, transparent display board, and (4) 25 pack of Report Forms

Plastic dispensing tips for the PosiTector SST (10 pack)

Belt Clip for PosiTector gage bodies

100 pack - 125 mm for use with PosiTector SST Abrasives Test Kit

Pack of 5 thin plastic lens shields to protect PosiTector display from paint overspray. One lens shield included in every PosiTector purchase.

Additional glue, mixing sticks, palettes and cotton swabs for pull-off adhesion tests

Drilling template and drill bits to isolate test area for pull-off adhesion tests, ideal for thicker coatings on concrete.

Ideal for cutting or scoring through a coating around the edges of a dolly (pull stub) to isolate a specific diameter test area and remove excess glue, if required.

Interchangeable stand-off allows a PosiTest ATM50 or ATA50 to pull 10, 14 and 20 mm dollies. Ideal for high bond strength finishes such as coatings on metal.

Interchangeable stand-off allows a PosiTest ATM20 or ATA20 to pull 50 mm dollies. Ideal for lower bond strength finishes such as coatings on wood, concrete and plastic.

Interchangeable stand-off allows a PosiTest ATM or ATA to pull 50 mm x 50 mm square dollies conforming to BS EN 12004-2. Ideal for cementitious adhesive for tiles.

Interchangeable stand-off allows a PosiTest ATM or ATA to pull 50 mm dollies conforming to ASTM C1583. Ideal for concrete surfaces and overlays.

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTest instrument.

Ideal for verifying the accuracy and operation of PosiTest Adhesion Testers and is an important component in fulfilling both ISO and in-house quality control requirements.

Loading fixtures, stubs for adhesion testing.

4-in-1 Replacement Blades for PosiTest CH Cross Hatch Tool

(1) Roll of ISO 8502-3 Tape for use with PosiTest DT test—25 mm wide

Roll of replacement tape for PosiTest CH Cross Hatch Adhesion Test

Add additional, reusable PosiTector CMM IS Smart probes

This lightweight device increases the utility of the PosiTest CMM allowing for quick and easy concrete moisture measurements on large surfaces without the need to bend or kneel.

For extending PosiTector CMM IS probe height in concrete slab thicknesses deeper than 4 inches

Replacement extraction tool for use with the PosiTector CMM IS.

Available in packs of 3.

Replacement fins for the PosiTector CMM IS

Available in packs of ten A-76/LR-44 coin cell batteries for use with the PosiTector CMM IS.

Replacement caps for use with the PosiTector CMM IS

A 10-pack of the Salt Solution for use with the PosiTector CMM IS

PosiTector Gage Bodies can be used with all PosiTector probes. Choose from Standard or Advanced models.

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

Ideal for checking calibration and operation of ultrasonic thickness gages and are an important component in fulfilling both ISO and in-house quality control requirements.

Convenient hard shell case for carrying a PosiTector gage body and multiple probes

Use for continuous operation. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTector instrument.

Every PosiTector 200 and PosiTector UTG ships with (1) bottle of Ultrasonic couplant.  Additional 4oz. bottles are available (sold in cases of 12). MSDS

Belt Clip for PosiTector gage bodies

Pack of 5 thin plastic lens shields to protect PosiTector display from paint overspray. One lens shield included in every PosiTector purchase.

PosiTector Gage Bodies can be used with all PosiTector probes. Choose from Standard or Advanced models.

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

Convenient hard shell case for carrying a PosiTector gage body and multiple probes

Use for continuous operation. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTector instrument.

Ideal for checking the operation of durometers.

Helps reduce operator influence by ensuring the probe is placed perpendicular in a controlled, repeatable way.

For use with threaded mounts in other test stands and calibrators.

For visual assessment of scratch and gouge marks

Replacement Blades (qty 10) for PosiTest PT Pencil Sharpener

Available as a complete set of 14 or as a 12 pack for individual hardnesses

Belt Clip for PosiTector gage bodies

Includes additional spare indentor tips (2pk) with replacement tool for the PosiTector BHI.

For verifying the operation of Barcol hardness impressors. Choose from hard, soft, or extra soft aluminum alloys. (Pack of 5)

For zeroing worn or replaced indentors on the PosiTector BHI.

Pack of 5 thin plastic lens shields to protect PosiTector display from paint overspray. One lens shield included in every PosiTector purchase.

Shoulder Strap for the PosiTest HHD Basic Kit and PosiTector Protective Carry Cases

‍

Replacement Li-ion batteries for the PosiTest HHD series

Converts the PosiTest HHD to a wand-type instrument

102mm/4" Conductive Rubber Paddle for PosiTest HHD

Thread onto rolling springs and attach to the Spring Connector for the PosiTest HHD series

43 cm (17") Extension Rod for PosiTest HHD C

Adaptable Sponge Hardware for a variety of test configurations with the PosiTest LPD

Choose between 13 cm (5") and 50 cm (20") rods for PosiTest HHD

Connect the PosiTest HHD to DeFelsko or SPY rolling spring electrodes

Converts the PosiTest LPD Low voltage Pinhole Detector into a cabled-wand style unit.

Stainless steel fan brush for PosiTest HHD series — 152 mm (6”)

For verification of electrical resistance

Connect to spring and brush electrodes to PosiTest HHD from other manufacturers

Pinholes can be so miniscule that water has difficulty reaching the conductive substrate underneath. Use a surfactant (wetting agent) to lower the surface tension of the water.

Neoprene half-circle brush electrode for PosiTest HHD series—good for pipes 50 to 127 mm / 2 to 5 inches

‍

Standalone voltmeter (crest meter, jeep meter) for verifying the accuracy and operation of pulse or continuous type DC holiday detectors

‍

Extend the PosiTest LPD base rod an additional 0.3 m (1')

610 mm (24") roller sponge for quick inspection over large areas with the PosiTest LPD

‍

Steel pipe electrodes for PosiTest HHD series — assorted sizes available: 10 to 91 cm (4 – 36”) Rolling springs include two pre-installed spring couplers.

Includes adaptable sponge hardware and accessories to convert the PosiTest LPD Basic Kit into a PosiTest LPD Complete Kit.

Stainless steel flat wire brush electrodes for PosiTest HHD series — assorted sizes available: 5 to 120 cm (2 – 48”)

PosiTector Gage Bodies can be used with all PosiTector probes. Choose from Standard or Advanced models.

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

Use for continuous operation. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

10 pack of replacement cleaning wipes for the PosiTector GLS

Belt Clip for PosiTector gage bodies

Pack of 5 thin plastic lens shields to protect PosiTector display from paint overspray. One lens shield included in every PosiTector purchase.

Six (6) replacement engraved ID tags for PosiTest OTL temperature probes

A wide variety of temperature probes are available for the PosiTest OTL with 1.8, 3.6, or 6 m (6', 12', or 20') stainless steel braided cables (sold separately).

Reusable Bresle Test patch with Standard or Flexible magnetic ring for soluble salt testing

Latex Bresle Test patch with easy-open tabs and low-tack adhesive for easy removal for soluble salt testing

Self-adhesive, polyurethane Bresle Test patches for soluble salt testing

PosiTector Gage Bodies can be used with all PosiTector probes. Choose from Standard or Advanced models.

PosiTector bodies accept all PosiTector probes easily converting from a coating thickness gage to a surface profile gage, dew point meter, soluble salt tester, hardness and ultrasonic thickness gage.

Dew Point Meter Logger attaches to steel structures to measure and record environmental parameters independently for up to 200 days.

Round-end plastic rubbing tool to compress replica film on the blasted surface (Pack of 10)

Battery-operated and light weight, this Bluetooth Printer prints readings and statistical summaries via Bluetooth from Advanced models.

Verify accuracy/operation of coating thickness gages. Important component of fulfilling both ISO/QS-9000 and in-house quality control requirements with a measurement accuracy traceable to NIST or PTB.

For use with existing conductivity meters. Try the revolutionary, reusable Bresle Method PosiPatch with a low cost trial pack.

Ideal for checking calibration and operation of ultrasonic thickness gages and are an important component in fulfilling both ISO and in-house quality control requirements.

Convenient hard shell case for carrying a PosiTector gage body and multiple probes

Economical alternative to Coated Metal Plates, with a reduced accuracy. Ideal for protecting the PosiTector probe tip.

For use with the innovative PosiPatch. Holds Bresle test patches on steel surfaces without leaving any messy residue.

Measures the concentration of water-soluble contaminates in blast cleaning abrasives

A lightweight, portable device that allows you to extend the reach of your PosiTector 6000 regular cabled probes.

Each roll of Testex Tape includes 50 pieces (Impressions)

Used to verify the accuracy and operation of all Testex micrometers. Ideal for fulfilling both ISO and in-house quality control requirements. Includes Certificate of Calibration traceable to PTB.

‍

Use for continuous operation. This kit supplies several alternate power solutions for your battery-operated PosiTector. Operate your gage without the need for batteries.

Purified, ion-free water to be used with the PosiTector SST, 250 ml or 1 l

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTector instrument.

Additional glue, mixing sticks, palettes and cotton swabs for pull-off adhesion tests

Drilling template and drill bits to isolate test area for pull-off adhesion tests, ideal for thicker coatings on concrete.

To verify accuracy of PosiTector SST probe

Every PosiTector 200 and PosiTector UTG ships with (1) bottle of Ultrasonic couplant.  Additional 4oz. bottles are available (sold in cases of 12). MSDS

Shoulder Strap for the PosiTest HHD Basic Kit and PosiTector Protective Carry Cases

‍

Ideal for cutting or scoring through a coating around the edges of a dolly (pull stub) to isolate a specific diameter test area and remove excess glue, if required.

Replacement Li-ion batteries for the PosiTest HHD series

Interchangeable stand-off allows a PosiTest ATM50 or ATA50 to pull 10, 14 and 20 mm dollies. Ideal for high bond strength finishes such as coatings on metal.

Converts the PosiTest HHD to a wand-type instrument

Interchangeable stand-off allows a PosiTest ATM20 or ATA20 to pull 50 mm dollies. Ideal for lower bond strength finishes such as coatings on wood, concrete and plastic.

Interchangeable stand-off allows a PosiTest ATM or ATA to pull 50 mm x 50 mm square dollies conforming to BS EN 12004-2. Ideal for cementitious adhesive for tiles.

102mm/4" Conductive Rubber Paddle for PosiTest HHD

Thread onto rolling springs and attach to the Spring Connector for the PosiTest HHD series

43 cm (17") Extension Rod for PosiTest HHD C

For best results when acquiring 2D/3D parameters and images, it is recommended to use the supplied burnishing ball instead of the high accuracy burnishing tool.

Adaptable Sponge Hardware for a variety of test configurations with the PosiTest LPD

Interchangeable stand-off allows a PosiTest ATM or ATA to pull 50 mm dollies conforming to ASTM C1583. Ideal for concrete surfaces and overlays.

Choose between 13 cm (5") and 50 cm (20") rods for PosiTest HHD

Used to check PosiTector RTR peak height accuracy (RTR H and RTR 3D). One check shim is included with each probe.

Connect the PosiTest HHD to DeFelsko or SPY rolling spring electrodes

Converts the PosiTest LPD Low voltage Pinhole Detector into a cabled-wand style unit.

For best results and to minimize the migration of adhesive from the tape to the probes measurement system, DeFelsko recommends using the supplied tape holder.

Stainless steel fan brush for PosiTest HHD series — 152 mm (6”)

For verification of electrical resistance

Connect to spring and brush electrodes to PosiTest HHD from other manufacturers

Ideal for checking the operation of durometers.

Pinholes can be so miniscule that water has difficulty reaching the conductive substrate underneath. Use a surfactant (wetting agent) to lower the surface tension of the water.

To clean the test surface of debris prior to burnishing

Neoprene half-circle brush electrode for PosiTest HHD series—good for pipes 50 to 127 mm / 2 to 5 inches

‍

Used to verify the operation of Testex and other spring micrometer replica tape readers

Helps reduce operator influence by ensuring the probe is placed perpendicular in a controlled, repeatable way.

Standalone voltmeter (crest meter, jeep meter) for verifying the accuracy and operation of pulse or continuous type DC holiday detectors

‍

Pre-moistened with isopropyl alcohol to clean residual adhesive and debris from the PosiTector RTR and RTR 3D anvils helping to ensure an accurate test.

Extend the PosiTest LPD base rod an additional 0.3 m (1')

610 mm (24") roller sponge for quick inspection over large areas with the PosiTest LPD

‍

Heavy-duty, waterproof Pelican cases complete with a custom foam insert to securely hold your PosiTest instrument.

Ideal for verifying the accuracy and operation of PosiTest Adhesion Testers and is an important component in fulfilling both ISO and in-house quality control requirements.

Steel pipe electrodes for PosiTest HHD series — assorted sizes available: 10 to 91 cm (4 – 36”) Rolling springs include two pre-installed spring couplers.

For use with threaded mounts in other test stands and calibrators.

Burnishing tool includes a built-in spring mechanism ensuring that consistent force is used, regardless of how hard the tool is pressed against the surface

Add additional, reusable PosiTector CMM IS Smart probes

Loading fixtures, stubs for adhesion testing.

Includes adaptable sponge hardware and accessories to convert the PosiTest LPD Basic Kit into a PosiTest LPD Complete Kit.

Stainless steel flat wire brush electrodes for PosiTest HHD series — assorted sizes available: 5 to 120 cm (2 – 48”)

1x, 2x, 5x, and 10x replacement tips sold individually

ICRI Concrete Surface Profile Chips available with or without Technical Guideline

4-in-1 Replacement Blades for PosiTest CH Cross Hatch Tool

For visual assessment of scratch and gouge marks

Replacement Blades (qty 10) for PosiTest PT Pencil Sharpener

Available as a complete set of 14 or as a 12 pack for individual hardnesses

(1) Roll of ISO 8502-3 Tape for use with PosiTest DT test—25 mm wide

Replacement dust tape comparator, transparent display board, and (4) 25 pack of Report Forms

Roll of replacement tape for PosiTest CH Cross Hatch Adhesion Test

10 pack of replacement filters for the PosiTector DPM L and PosiTector DPM L+

10 pack of replacement cleaning wipes for the PosiTector GLS

Plastic dispensing tips for the PosiTector SST (10 pack)

This lightweight device increases the utility of the PosiTest CMM allowing for quick and easy concrete moisture measurements on large surfaces without the need to bend or kneel.

Belt Clip for PosiTector gage bodies

Six (6) replacement engraved ID tags for PosiTest OTL temperature probes

A wide variety of temperature probes are available for the PosiTest OTL with 1.8, 3.6, or 6 m (6', 12', or 20') stainless steel braided cables (sold separately).

Available in packs of five (5) CR2032 batteries.

For use with the PosiTector DPM L.

Optional Lock for PosiTector DPM L Series.

Keeps both PosiTector DPM L and PosiTector DPM L+ safe and secure.

For extending PosiTector CMM IS probe height in concrete slab thicknesses deeper than 4 inches

Replacement extraction tool for use with the PosiTector CMM IS.

Available in packs of 3.

Used to verify the accuracy and operation of surface profile depth micrometers

Hand-held Surface Temperature Probe and Liquid Temperature Probe. For use with PosiTector DPMS probes only.

Includes additional spare indentor tips (2pk) with replacement tool for the PosiTector BHI.

Replacement fins for the PosiTector CMM IS

Available in packs of ten A-76/LR-44 coin cell batteries for use with the PosiTector CMM IS.

Used to check the operation of PosiTector RTR 3D peak density measurement (for use with the PosiTector RTR 3D only).

Certified Polystyrene Blocks are for use with gages that measure over 1500 µm (60 mils).

Used to protect the PosiTest PC probe transducer (Qty. 2)

Every PosiTest AIR comes complete with (4) bottles of Test Solution. Additional bottles are available in cases of (16) 8 oz. bottles.

100 pack - 125 mm for use with PosiTector SST Abrasives Test Kit

Replacement caps for use with the PosiTector CMM IS

Ideal for use on thin, soft coatings to protect coatings from unnecessary wear while using Scan or Fast mode to measure large objects

Helps reduce adverse operator influence by ensuring the PosiTector 6000 probe is placed perpendicular to the part’s surface in a controlled, repeatable way.

For verifying the operation of Barcol hardness impressors. Choose from hard, soft, or extra soft aluminum alloys. (Pack of 5)

Replacement probe tips for the PosiTector SPG — 2 angles available: 60° or 30°